uber fast break-in
+2
wala258
jusay_mitch29
6 posters
:: Cuber's Talk :: Off Topic
Page 1 of 1
uber fast break-in
https://pinoyspeedcubers.forumotion.com/cubing-videos-f6/super-fast-cube-break-in-astig-to-t3218.htm
has anyone tried this... i think it'll make the screws hot enough to melt the core.... tinry ko kasi i break in ung diy ko dati uminit ung screw tas na loose thread xa... so my question is ano g pede gawin para ndi uminit ung screw..... sori kung dito ko pinost pinag mamadali na ako dito sa pc tataas daw ung kuryente e nandito ako sa off topic kaya dito ko na pinost... paki move na lang kung kailangan
has anyone tried this... i think it'll make the screws hot enough to melt the core.... tinry ko kasi i break in ung diy ko dati uminit ung screw tas na loose thread xa... so my question is ano g pede gawin para ndi uminit ung screw..... sori kung dito ko pinost pinag mamadali na ako dito sa pc tataas daw ung kuryente e nandito ako sa off topic kaya dito ko na pinost... paki move na lang kung kailangan
jusay_mitch29- 4x4x4
- Number of posts : 1245
Age : 30
Registration date : 2008-01-28
Re: uber fast break-in
skn auz naman.. ginawa ko to.. wala namang problema, naging maganda at dumulas ung cube lalo na pag nalube na ito..
wala258- 2x2x2
-
Number of posts : 426
Age : 34
Location : Antipolo City
Registration date : 2008-02-25
Re: uber fast break-in
wat materials did u use?wala258 wrote:skn auz naman.. ginawa ko to.. wala namang problema, naging maganda at dumulas ung cube lalo na pag nalube na ito..
Re: uber fast break-in
MaZtR HaXoR wrote:wat materials did u use?wala258 wrote:skn auz naman.. ginawa ko to.. wala namang problema, naging maganda at dumulas ung cube lalo na pag nalube na ito..
driller tapos box na inukit specialy for single layer sa 3x3x3....
amoy sunog ung cube pagtapos... haha
Re: uber fast break-in
S a s o r i wrote:MaZtR HaXoR wrote:wat materials did u use?wala258 wrote:skn auz naman.. ginawa ko to.. wala namang problema, naging maganda at dumulas ung cube lalo na pag nalube na ito..
driller tapos box na inukit specialy for single layer sa 3x3x3....
amoy sunog ung cube pagtapos... haha
wat box po? pls specify how to do and wer d get it
Re: uber fast break-in
i think bottom of a 1.5 litter coke is better since at the bottom may part ng plastic na matigas gagawa ka na lang ng butas dun para sa tatlong grippers ng drill... i'll try it kapag may bago kong diy
jusay_mitch29- 4x4x4
- Number of posts : 1245
Age : 30
Registration date : 2008-01-28
Re: uber fast break-in
that's insane!!! hahaha!!!! pero ang lufet... hmm.... para maiwasan ang overheating(try mo to baka effective...), ask an assitant to pour some cold water while doing that "break-in"
para di masyadong uminit yung screws while spinning at high speeds.... eto p pala isa, kung meron kang grease na pang high temp (like ung ginagmit sa mga bearing ng kotse) lagay mo sa screws then spin it like hell... mangingitim nga lng yung loob ng center cap mo dhil sa nasunog sa grease, pero safe na safe ang cube mo... linisin mo n lng pagkatpos... peace out!!!
para di masyadong uminit yung screws while spinning at high speeds.... eto p pala isa, kung meron kang grease na pang high temp (like ung ginagmit sa mga bearing ng kotse) lagay mo sa screws then spin it like hell... mangingitim nga lng yung loob ng center cap mo dhil sa nasunog sa grease, pero safe na safe ang cube mo... linisin mo n lng pagkatpos... peace out!!!
kulantroz- 2x2x2
-
Number of posts : 147
Age : 38
Location : Taguig City
Registration date : 2008-03-23
Re: uber fast break-in
MaZtR HaXoR wrote:S a s o r i wrote:MaZtR HaXoR wrote:wat materials did u use?wala258 wrote:skn auz naman.. ginawa ko to.. wala namang problema, naging maganda at dumulas ung cube lalo na pag nalube na ito..
driller tapos box na inukit specialy for single layer sa 3x3x3....
amoy sunog ung cube pagtapos... haha
wat box po? pls specify how to do and wer d get it
box po ng sapatos ung makapal na parte nun ang kunin mo..
wala258- 2x2x2
-
Number of posts : 426
Age : 34
Location : Antipolo City
Registration date : 2008-02-25
Re: uber fast break-in
i think i'll just buy another core kung ma-loose thread man e may back-up ako hihihihhi... nid kasi natin ang friction to break in e... so ndi pede ang lubricant or coolant... i'm not sure though
jusay_mitch29- 4x4x4
- Number of posts : 1245
Age : 30
Registration date : 2008-01-28
Re: uber fast break-in
i think this should be done on non DIY cubes....
jerjero- 2x2x2
-
Number of posts : 402
Age : 34
Location : DasmariƱas Cavite
Registration date : 2007-06-24
Similar topics
» Uber fast solve!!!!!
» Bryan Manzana's Uber-Fast Solve!
» TRU Trinoma cube is UBER rough!!
» i exist!sem break..
» Break-in question
» Bryan Manzana's Uber-Fast Solve!
» TRU Trinoma cube is UBER rough!!
» i exist!sem break..
» Break-in question
:: Cuber's Talk :: Off Topic
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum
|
|